Career

DIN EN 10216-2 PDF

Buy DIN EN SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES – TECHNICAL DELIVERY CONDITIONS – PART 2. DIN EN Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 2: Non-alloy and alloy steel tubes with specified elevated. ​Manufacturing program with average wall thickness (EN ). Vallourec supplies seamless steel tubes for pressure purposes in accordance with.

Author: Nijind Nikora
Country: Comoros
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 May 2008
Pages: 133
PDF File Size: 14.9 Mb
ePub File Size: 17.52 Mb
ISBN: 146-2-26678-456-9
Downloads: 20231
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigul

Din En 2 Steel Pipe, Din En 2 Steel Pipe Suppliers and Manufacturers at

Tensile testing at elevated temperature diin 8. We have no document history for this standard. Automatic full peripheral ultrasonic testing of seamless steel tubes for the detection of transverse imperfections. Welded steel tubes for pressure purposes — Technical delivery conditions — Part 2: The ends shall be free from excessive burrs. This requirement does not apply to surface imperfection with a depth equal or less 0,3 mm 8.

Tubular Products (EN )

The pipes are manufactured from carbon and low-alloy steel grades which are resistant to loads under high pressure and temperatures. In the event that the purchaser does not indicate a wish to implement any of these options at the time of ordering, the 10216- shall be supplied in accordance with the basic specification see 6.

Restriction on copper and tin content see table 2. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. The test temperature shall be specified at the time of ordering.

een You may use these HTML tags and attributes: The requirements of this European Standard rule when they differ from those in the standards and 102162- referred to below: Product analysis for the tubes shall be supplied.

  3D GRAFIKPROGRAMMIERUNG PDF

Page 9 EN Welded steel tubes for pressure purposes — Technical delivery conditions — Part 4: Many years of experience. EN and prEN Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.

DIN, the German Institute for Standardization, develops norms and standards as a service to industry, the state and society as a whole. ENDesignation systems for steels – Part 1: Please first verify your email before subscribing to alerts. Where test pieces of least 5 mm width cannot be sn, the tubes shall not be subjected to impact testing. Non alloy and alloy steel tubes with specified elevated temperature properties; German version EN Seamless steel tubes dih pressure purposes — Technical delivery conditions Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties Specifies the technical delivery conditions in two test dkn of electric welded tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel….

When tubes are specified in the order by d, dmin or Tmin the following equations, all in millimetres, shall apply for the calculation of outside diameter Dc, inside diameter dc and wall thickness Tc, instead of D, d and T for the relevant requirements in 01216-2 8.

List of standards Mass calculator Fundusze europejskie. Unless option 16 is specified, the selection of the test method is at the discretion of the manufacturer.

Tubular Products (EN 10216-2)

ENDesignation systems for steels – Part 2: This standard is also available to be included in Standards Subscriptions. Subscription pricing is determined by: In the case of inspection report 3. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.

  HOODIA D387 PDF

The pipes are manufactured with the diameters between 21,3 — mm and with the wall thickness 10216-22 up to mm in the case of hot rolling, and with the diameters between 10,2 — and with the wall thickness of up to 12,5 mm in the case of cold drawing. In case of dispute the method used shall be agreed between manufacturer and purchaser taking into account CR Impact testing see table 4. To consider the test unit as conforming, after testing the second set, the following conditions shall be satisfied simultaneously: Dn the manufacturer’s discretion: NOTE When welding tubes produced in accordance with this Part of this ENaccount should be taken of the fact that the behaviour of the steel during and after welding is dependent not only on the steel, but also on the applied heat treatment and the conditions of preparing for and carrying out the welding.

EN 10216-2 Seamless Carbon Steel Tube

They are used for the construction of power engineering appliances such as: For the tolerances, see 8. Standards Subsctiption may be the perfect solution. The tube section shall be flattened in a press until distance H between platens reaches the value given by the following equation: Unless option 15 is specified the wall thickness shall be measured at both tube ends.